PENERAPAN METODE MODE KEGAGALAN DAN ANALISA EFEK PADA PROSES PERAKITAN PRODUK MEJA OPERASI MANUAL
Abstract: The purpose of this
research was to identify the cause of Manual Operating
Table Design Failure using
FMEA (Failure Mode
and Effect Analysis)
method viewed from assembly process.
The severity, occurrence
and detection ratings
of the potential failure modes
could be determined, and then all of them were multiplied to get Risk Priority
Number (RPN) value. The recommendation
to prevent the failure from
occurring in Manual
Operating Table design
was given if
the RPN value exceeded 90 limits.The result of
analysis on the FMEA process of sub assembly gave that the potential failure would
occur during installing
the midle or
side valve covering
bolt with verpak (RPN = 189), seal settle (RPN = 108), bushing
trenden lift (RPN =126), right kneerest
rack settle (RPN
= 96), and
left kneerest rack settle
(RPN = 96). While
for FMEA process
of final assembly,
the potential failure
would occur during installing
Hi-Lo pump sub assembly and handle pump sub assembly to boom assembly (RPN =
96), installing the lateral neck sub assembly at the Hi -Lo pump assembly (RPN
= 108), installing the mattress frame assembly (RPN = 120), and installing the
kneerest sub assembly at mattress f rame assembly (RPN = 108).Based on
the RPN value
calculation conducted, some
recomended actions were given to prevent the failures on the process of assembling.
Keywords: FMEA Process, Severity,
Occurrence, Detection, RPN
Kode Jurnal: jptmesindd090035

Artikel Terkait :
Jp Teknik Mesin dd 2009
- PEMODELAN DAN SIMULASI SISTEM PEMBANGKIT TURBIN GAS PLTGU TANJUNG PRIOK
- PENGEMBANGAN ALGORITMA PEMBANGKITAN G-CODE MESIN PERKAKAS CNC OKUMA&HOWA BERFASILITAS AUTOMATIC TOOL CHANGER DAN INDEXING PADA SOFTWARE CaSTPro
- DEVELOPMENT OF AUTO-GENERATING AERODYNAMIC LOADS FOR WING-BOX FINITE ELEMENT MODEL BASED ON SCHRENK METHOD
- EVALUASI POLA FUNGSI RESPON FREKUENSI PADA RESPON GETARAN BANTALAN GELINDING
- DEVELOPMENT OF COAXIAL ROTOR MICRO UNMANNED AERIAL VEHICLE
- DESIGN AND TESTING OF COAXIAL ROTOR DUCTED FAN VTOL UAV
- ANALISIS LOMPAT VERTIKAL TIPE SQUAT DENGAN MODEL SISTEM BENDA JAMAK
- PENGHEMAT BAHAN BAKAR PADA KOMPOR GAS RUMAH TANGGA
- THE APPLICATION OF CONSTRAINT PROPAGATION TECHNIQUE FOR CONCEPTUAL AIRCRAFT DESIGN
- PENYELESAIAN PENDEKATAN PROBLEM KONTAK HERTZIAN PADA KASUS KONTAK ANTARA RODA DAN REL
- KAJI EKSPERIMENTAL CIRI GETARAN PADA BANTALAN ROL DENGAN PEMBEBANAN STATIK
- KAJIAN EKSPERIMENTAL SISTEM PENGAPIAN KONVENSIONAL DITINJAU DARI ASPEK PERAWATAN PREDIKTIF TERHADAP KONSUMSI BAHAN BAKAR PADA ENGINE TOYOTA KIJANG TYPE 5K
- STUDI EKSPERIMENTAL MESIN REFRIGERASI SIKLUS KOMPRESI UAP MENGGUNAKAN REFRIGERAN HIDROKARBON SUBSTITUSI R22 PADA KONDISI TRANSIENT
- ANALISIS ENERGI PADA SISTEM ROTARY KILN UNIT INDARUNG IV, PT. SEMEN PADANG
- ANALISIS SIFAT FISIK DAN KIMIA BIODIESEL DARI MINYAK JELANTAH SEBAGAI BAHAN BAKAR ALTERNATIF MOTOR DIESEL
- ANALISIS PENGENDALIAN MOTOR DC MENGGUNAKAN LOGIKA PID DENGAN MIKRO KONTROLER ATMEGA 8535
- UJI PRESTASI KERJA MESIN PEMBUATAN SANTAN KERING SISTEM SPRAY DRYING
- Review Metalurgi Las Baja Tahan Karat
- Review Pengelasan Baja dan Besi Cor Kelabu
- Kondisi Pemotongan Optimum Proses Pembubutan Keras Baja Perkakas Aisi O1 Menggunakan Pahat Keramik
- Studi Cacat Lasan Pada Baja Struktural Dan Pencegahannya
- Analisa Dfa Pada Katup Pengatur Kecepatan Silinder Pneumatik (Dfa Analysis On Flow Control Valve Of Pneumatic Cylinder)
- Analisis Karakteristik Kebisingan Knalpot Komposit Pada Mobil Toyota Kijang Tipe 7K
- PENGARUH PERSEPSI MAHASISWA TENTANG VARIASI MENGAJAR DOSEN TERHADAP HASIL BELAJAR DALAM MATA KULIAH TEKNIK PERMESINAN
- PENINGKATAN PEMAHAMAN MAHASISWA TENTANG OVERHAUL MOTOR BENSIN MENGGUNAKAN INSTRUCTIONAL MATERIALS PADA MATA KULIAH PRAKTIK PERAKITAN OTOMOTIF II